# PoE LAN

Complying with 802.3af/at PoE standard, the outdoor 4G router uses a LAN cable to transmit both DC power and Ethernet data. A 48Volt standard PoE injector and 10-meter outdoor-grade LAN cable are included in the package.

## **Connect to PoE Power**

Please refer to the image and follow the below steps to connect the EZR33T router to the PoE injector.

<figure><img src="/files/KBw6EfRNedYm7NDFElpH" alt=""><figcaption></figcaption></figure>

### Step-by-Step

1. **Take apart the PoE gland.**\
   Turn the white color cap off from the gland in an anti-clockwise direction.\
   Then, push out the orange color stopper inside the barrel connector.
2. **Take one end of the LAN cable through the cap.**
3. **Put the LAN cable through the barrel screw** and plug in the PoE & LAN port on the motherboard.
4. **Clamp the stopper on the LAN cable** and settle it in the barrel.\
   \* The smaller end of the orange color stopper should face the outside.
5. **Turn the cap in the clockwise direction** to tighten it on the barrel screw.
6. Connect another end of the LAN cable **to the PoE port on the PoE injector.**
7. Connect the AC plug on the PoE injector to an electrical outlet until all the steps below are set up.

#### Remarks:

**Exchange AC Plug on PoE Injector --** To exchange the AC plug on the PoE injector, press and hold the Push button, then push the AC plug upward to take it off. Then install another AC plug on it.

**Exchange LAN Cable --** A 10-meter outdoor grade LAN cable is included in the package. You can use a max 50-meter LAN cable. Use Cat5 or higher-grade LAN cable and ensure it's the TIA/EIA568B wiring. Please refer to the below image. An outdoor-grade LAN cable is recommended for use in the outdoor environment. There will be a distinct attenuation on the Ethernet signal when the LAN cable is longer than 50 meters. You can use a PoE extender to reduce the attenuation on a longer LAN cable.

## PoE Ethernet Connection

There are two RJ45 ports on the PoE injector. The PoE port outputs 48Volt 0.5Amps DC power to boot up the 4G router.&#x20;

After the 4G router is connected to the mobile network, we can connect a computer, another router, or network switch to the LAN port on the PoE injector and get an Ethernet connection.

Make sure the computer or another router turns on DHCP client mode. Then, they could automatically obtain a local IP address and connect to the internet.

## Alternative Power

### PoE Switch

You can use an IEEE802.3af/at standard PoE switch to power up the 4G router. Connect the 4G router to one of the PoE ports on the PoE switch.

### 12Volt Power

We can boot up the outdoor router with a range of 9\~48Volt DC power. Use the DC plug to connect to the DC socket on the motherboard. The PoE gland can take an extra DC power cable. The suggested DC power current is 12Volt 1.5Amps.

‌If both DC power and PoE power are connected, the outdoor router will use the first connected power source. The router seamlessly switches to another power source if one cuts off power.


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://ezr33t.router.works/sim-card-poe/poe-lan.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.